A lot smaller than I was expecting. Smaller than my T3 heater.
My AC Infinity Jones
- Thread starter Shane Karmann
- Start date
DarkWeb
Probably My Fault
Yeah, I was surprised by the size also.
DCcan
Stoned on the Rocks
I can't believe they made it 4' ducting, 6 inch would quiet the whole thing down.
Also wish the fan would run on LO if the heat is on LO. Fan runs on 10 any time the heat is on.
It's pretty loud, loudest thing in the room.
Tiny intake filter was replaced with a 4"x8" adaptor with a larger, better filter.
Had a 4"x 6" exhaust adaptor so I used that. The 4x coated ducting from ACI was used, regular ducting would just fall apart after time I think.
Probably going to take off the ducting and use a 90 elbow to blow across the floor of tent
DCcan
Stoned on the Rocks
Put the exhaust duct and humidifier closer to the filtered intake duct, help stabilize the humidity and temps.
Mixes the air and recycles some of the heat hopefully.
Humidifier is running on its own sensor, rather than the AI controller sensors.
I haven't figured out if I can use the OUTSIDE sensor on the AI controller for that.
Mixes the air and recycles some of the heat hopefully.
Humidifier is running on its own sensor, rather than the AI controller sensors.
I haven't figured out if I can use the OUTSIDE sensor on the AI controller for that.
Last edited:
It is loud lol. Louder than the two exhaust fans running in my little room.
I replaced a T3 heater and that barely made any noise.
Anyone try the S9 fans yet?
Larger brushless EC motor with carbon steel gears,
acinfinity.com
Larger brushless EC motor with carbon steel gears,
CLOUDRAY S9, Grow Tent Clip Fan 9" with 10 Speeds and Dynamic Wind
Generate powerful crosswinds using the Cloudray S9 grow tent clip fan. This 9-inch system features ten adjustable speeds to support vigorous plant growth.
acinfinity.com
Thurston
Howell III
Anyone try the S9 fans yet?
Larger brushless EC motor with carbon steel gears,
CLOUDRAY S9, Grow Tent Clip Fan 9" with 10 Speeds and Dynamic Wind
Generate powerful crosswinds using the Cloudray S9 grow tent clip fan. This 9-inch system features ten adjustable speeds to support vigorous plant growth.
Take my money!
Nobody stopped me
Dboybudz
Dazed and Confused 😛
Well if it's shit you can get Annie to yell at em, lol
Well if it's shit you can get Annie to yell at em, lol
I was gonna send her to yell at HLG, but I ended up with a better light.
Dboybudz
Dazed and Confused 😛
Yea I remember, that's why i said,lol
They’re huge!
S6 grill for size comparison
DCcan
Stoned on the Rocks
Ordered a soil sensor, can pair it with the UIS outlet contoller and a pump.
Just going to use it to gauge dry/ wet numbers for now. Got other work to do before that hobby.
Looks like you add the extension when you transplant.
Can you plug additional sensors into UIS contol ports, anyone know?
Seems like you would have to, with photo receptors, co2, water sensors, ph modules
Just going to use it to gauge dry/ wet numbers for now. Got other work to do before that hobby.
Looks like you add the extension when you transplant.
Can you plug additional sensors into UIS contol ports, anyone know?
Seems like you would have to, with photo receptors, co2, water sensors, ph modules
I think anything with a uis port will work with the controllers
This fan is pretty slick. You can control the oscillating angle. A lot heavier too with a metal clamp
Dboybudz
Dazed and Confused 😛
That's awesome plus add the light mimics sunrise and sunsets.
Similar threads
